Ranges · Cooktops · Electric-to-Gas · Same-Day

Gas Stove, Range & Cooktop Hookup in Chicagoland

Licensed gas stove and range installation for homes across Chicago and the suburbs

Whether you're dropping in a new range or running gas to the kitchen for the first time, Midwest Gas Pipe Repair handles the line, the connector, and the leak test the right way. Lines from $199 — call (708) 381-2959 anytime for a 24/7 callback across Chicago and the suburbs.

Call (708) 381-2959 Request Stove Hookup
Licensed Pros Only 24/7 Callback Routing Chicago & Suburbs

New stove installs — line, shutoff, flex connector, leak test

A clean gas stove install is more than sliding the range into place. We start at the gas line itself — confirming it's the right size to carry the burner load your stove needs, measured in BTU, so every burner and the oven fire fully without starving the line. From there, the job comes together in four parts:

  • A dedicated shutoff valve behind the range, so you can isolate the stove without killing gas to the whole house
  • A new, properly rated flex connector — the yellow appliance hose that links the rigid pipe to the stove's gas inlet
  • A snug, leak-free connection using gas-rated thread sealant, never plumber's tape meant for water
  • A full leak test — we brush every joint with soap solution and watch for bubbles, and pressure-test the line where the work calls for it

We do this work as part of our broader gas appliance hookups across Naperville, Oak Park, and the rest of Chicagoland. Nothing gets lit until the line proves tight.

Replacing an old electric range with gas (running a new line)

Switching from electric to gas is one of the most common requests we get, and it's a bigger job than a like-for-like swap — because there's usually no gas line behind the stove yet. We tap the nearest sized branch in the basement or crawlspace, run new pipe to the kitchen, and add a shutoff and connector at the range location. If the run is long or feeds other appliances too, we may upsize the pipe so the stove gets full pressure.

This is true gas line installation, and where the new pipe ties into rigid runs we'll often use CSST — flexible corrugated stainless steel tubing that snakes through framing more easily than black iron. If any portion of the work means digging outside, Illinois law requires a JULIE (811) locate before we break ground. Our guide on how to convert electric to gas range walks through what to expect from start to finish.

Drop-in cooktops and slide-in ranges — clearance & flex specifics

Drop-in cooktops and slide-in ranges look simple from the front, but the gas connection hides inside a tight cabinet or under the counter — and that changes how we route the line. The flex connector has to reach the appliance inlet without kinking, stretching, or getting pinched when the unit slides back against the wall. A crimped connector is a failure waiting to happen.

  • We confirm the manufacturer's required clearance to combustibles around the burners and behind the unit
  • We position the shutoff valve where you can actually reach it, not buried behind the appliance
  • We size and route the connector so there's gentle slack, never tension, at the inlet
  • For cooktops, we make sure the under-counter connection stays accessible for future service

Homeowners in Evanston and Hinsdale often pick slide-in models for the built-in look, and getting the gas geometry right is what makes that flush fit safe.

Why a cheap flex connector is the most common leak source

If a gas stove ever develops a leak, the flex connector is the usual suspect — not the rigid pipe. These connectors are consumable parts. An old one that's been moved during cleaning, a connector that's been reused from a previous install, or a bargain-bin hose with thin walls can crack, corrode at the fittings, or seep at the threads over time.

We never reuse a connector. Every stove install gets a brand-new, code-approved flex line rated for the gas load, with the fittings torqued correctly and tested. We also add a sediment trap (sometimes called a drip leg) — a short downward stub of pipe near the appliance that catches moisture and debris before they reach the burner valves. If you ever smell that rotten-egg odor near the stove, leave the home and call 911 or your utility — Peoples Gas in the city, Nicor in the suburbs — first; private-side work comes after the area is safe. When in doubt, our gas leak detection team can pinpoint the source.

Permits, code, and HOA / condo board sign-off

Most gas work on the private side of the meter is permitted work, and the rules vary across Cook, DuPage, Lake, and Will counties. A straightforward connector swap on an existing line is often a quick job, but running a new line — like an electric-to-gas conversion — typically needs a permit and inspection. Chicago runs its own plumbing and mechanical permit process; suburbs like Schaumburg, Arlington Heights, and Joliet each handle their own. We know the local norms and pull the right permit for your address.

If you live in a condo or an HOA community, there may be a second layer: the building or board often requires its own sign-off before any gas work begins, especially in shared-wall and high-rise buildings. We're happy to provide the license, insurance, and scope details your board needs. Doing it by the book keeps your homeowner's insurance valid and leaves you with a clean paper trail.

Cost: simple swap vs new line run

Stove hookup cost depends almost entirely on whether the gas line already exists. As a rough guide:

  • A simple swap — reconnecting a new stove to an existing, properly sized line with a fresh connector and shutoff — sits at the lower end and is one of our more affordable jobs
  • A new line run — the typical electric-to-gas conversion, where we install new pipe, a shutoff, a sediment trap, and pull a permit — runs higher because of the materials, labor, and inspection involved
  • Long runs, upsized pipe, finished walls or ceilings that need opening, and after-hours calls all add to the total

Repairs and basic hookups start from $199, but a full line run is its own project. The honest answer is that the spread is wide, and we'd rather price your actual kitchen than quote a number that doesn't fit. Get a written quote — every home is different.

Same-day vs scheduled appointments

Because we run a mobile, licensed crew 24/7, you have options. A new stove sitting in the box with an existing gas line behind it is usually a same-day or next-day appointment — we can often get a licensed pro to you fast and have you cooking that evening. An electric-to-gas conversion, on the other hand, is best scheduled, since it may involve a permit, an inspection, and a little more time on site.

If you're removing an old stove and won't replace it right away, don't leave the line open — it needs to be capped properly. Our walkthrough on how to cap a gas line after removing a stove explains why, and we can cap it for you on the same visit. Either way, call (708) 381-2959 and tell us your stove type and whether a gas line is already there; we'll tell you honestly whether it's a today job or a scheduled one, with 30-60 minute emergency dispatch available across Chicago and suburbs like Glenview, Oak Brook, and Bolingbrook.

Service areas for gas stove installation

Gas stove installation requests are routed across Chicago and the surrounding suburbs.

Need a Gas Stove or Range Hooked Up?

Call now or send the callback form. Let us know if it is a swap or a new line.

Call (708) 381-2959
Common Questions

Gas Stove Installation FAQs

It depends mostly on whether a gas line is already in place. A simple swap — connecting a new stove to an existing, correctly sized line with a fresh flex connector and shutoff — is one of the more affordable jobs and starts at the lower end. Running a new line for an electric-to-gas conversion costs more because it involves new pipe, a permit, and an inspection. Long runs, upsized pipe, and after-hours calls add to the total. Repairs and basic hookups start from $199, and we always provide a written quote before we begin — every home is different.
Yes. The catch is that there's usually no gas line behind an electric stove, so we run new pipe from the nearest sized branch to the kitchen, add a shutoff valve and sediment trap, and install the connector at the range. If the run is long or feeds other appliances, we may upsize the pipe so your stove gets full pressure. This is permitted work in most municipalities, so it's typically a scheduled appointment rather than same-day. We serve homes across Naperville, Oak Park, Evanston, and the rest of Chicagoland.
A like-for-like reconnection to an existing line is often a quick job, but running a new gas line — such as an electric-to-gas conversion — typically requires a permit and inspection. The rules vary across Cook, DuPage, Lake, and Will counties, and Chicago runs its own permit process separate from the suburbs. If you're in a condo or HOA, your building or board may also require its own sign-off. We know the local norms, pull the right permit for your address, and can provide the license and insurance details your board needs.
The yellow flex connector is a consumable part, and it's the most common leak source on a stove — not the rigid pipe. An old connector that's been moved during cleaning, one reused from a prior install, or a thin bargain hose can crack, corrode at the fittings, or seep at the threads over time. We never reuse a connector; every install gets a new, code-approved line sized to the stove's gas load, with fittings torqued and leak-tested. If you smell a rotten-egg odor near the stove, leave the home and call 911 or your utility (Peoples Gas or Nicor) first.
Often, yes. If your new stove is on hand and there's already a properly sized gas line and shutoff behind it, a hookup is usually a same-day or next-day appointment, and you can be cooking that evening. A new line run or electric-to-gas conversion is best scheduled because of the permit, inspection, and added time on site. Because we're mobile and operate 24/7, we offer fast dispatch — including 30-60 minute emergency response — across Chicago and suburbs like Schaumburg, Glenview, and Bolingbrook. Call (708) 381-2959 and we'll tell you honestly which it is.
Never leave an open gas line behind a removed stove — even with the shutoff closed, an open line is a hazard. The line needs to be capped properly with the correct fitting, and the cap should be leak-tested. We can cap it for you on the same visit, and our blog post on how to cap a gas line after removing a stove explains exactly why it matters. If you ever smell gas near an open or capped line, leave the area and call 911 or your gas utility first, then call us to make it safe.